your location:

Cases Center

bridgeport variable speed milling machine

bridgeport variable speed milling machine

Bridgeport Series I, 9" x 49" 3HP Variable Speed

Bridgeport Series I 9" x 49" 3HP Variable Speed Milling Machine Package. Bridgeport Milling Machine with Accessory Package as Shown: Acu-Rite® new 203 Series, 2 axis digital readout; Kurt DX6 6",Kurt DX6 Anglock Machine Vise 6" x 9" Opening; 11 Pc. R8 collet set with holder; Power Table Feed "X" Axis; Series I Standard Features Include:

Bridgeport 9 x 48" 3 HP 230v Variable Speed Pulley

Bridgeport 9 x 49" 2 HP Variable Speed Pulley Control 3 Phase Knee Milling Machine 36" Long Travel, 12" Cross Travel, 16" Knee Travel, 60 to 4200 Rpm, Variable Speed $20,814.17 Add to Cart

Milling Machine, Bridgeport, 1-1/2 HP, J Head

Bridgeport 1-1/2 HP Variable Speed Milling Machine, 9″ x 36″ Table, R-8 Spindle, 3 Phase 230/460 Volts, Serial #107193(1967)

SERIES I MILLING MACHINES Fab Central

2017-4-21 Variable Speed Dial “B”, Figure 2.3, visibly indicates, in windows, the speed range that themachine is operating in, 60 to 500 low range, 500 to 4200 high range.

Milling Variable Speed

Bridgeport J-head Variable Speed Milling Machine Year:1961, Serial:BR 55852, 42"L x 9"W-3"H Table, 5"Quill, Automatic Table Feed, Variable Speed Head(High/Low) Speeds: Low:80.135,210,355) High:660.1115,1750,2720) 1hp Motor 3Ph, 208-220/480 Volt, 15 Collet Tool Holder You will receive an invoice via email or Ebay for the full amount owed.

bridgeport-machine OHIO QUALITY

2021-2-11 Bridgeport Milling Machines find their way into most shops across the country. They become one the most used tools in any tool room. Like a hammer is to a carpenter, Bridgeport Mills into your tool room is a must. BASIC PRICE FOR 2J VARIABLE SPEED HEAD W/ The All New TAS IRON ELSR CONTROL BASE PRICE $ 7,500.00 OPTIONS INCLUDING INSTALLATION:

VARIABLE SPEED AND TIMING BELTS FOR MILLING

2016-2-8 bridgeport (4hp) 11172108 (4j863) 3430v493 $87.00 BRIDGEPORT 11172109 (4J865) 11172109 (4J865) $225.00 BRIDGEPORT 11182106 or 2J650 (40173) 1 1/8" X 42 Teeth $38.00

Bridgeport variable speed head eBay

2021-6-8 Bridgeport variable speed milling machine head. 2HP. Purchased with the intent of using and it sat on a shelf for the past 5 years so now its time to go. the high/low shifter goes in,the quill moves freely without any binding, the spindle turns free. the head does not

Bridgeport Milling Machine Manual The Curious Forge

2018-7-12 All parts can be found on page variable speed upper housing Replacing Collet Alignment screw inside spindle Bring the quill down about two inches Look on the back side of the quill and you will see a small set screw. Remove it This holds in the nosepiece on the bottom of the quill With set screw removed you can unscrew the nosepiece.

AC Variable Speed Drive H&W Machine Repair &

-Imports- No more hard to find variable drive replacement parts. -Convert- Your step pulley head into a more productive variable speed head in less than 1 hour with 65 to 5000 RPM's. -No holes to drill or tap on a Bridgeport variable speed or step pulley type milling machine. -2 year limited factory warranty.

BRIDGEPORT 1 1/2 HP VARIABLE SPEED VERTICAL

BRIDGEPORT 1 1/2 HP VARIABLE SPEED VERTICAL MILLING MACHINE WITH BRIDGEPORT SWIVEL VISE AND ASSORTED COLLETS CHROME WAYS, 9" x 42" TABLE. AML Stock #002572. 9” x 42” Bridgeport Vertical Milling Machine, Model 2J, S/N 156719. Table Size 9” x 42” Travels Long 26” Cross 12” Quill 5” Knee 16” Spindle Speeds 60-4200 RPM HP 1.5 220

BRIDGEPORT 2 HP VARIABLE SPEED MILLING

BRIDGEPORT 2 HP VARIABLE SPEED MILLING MACHINE WITH 9" x 48" TABLE, LONGITUDINAL POWER FEED AND CHROME WAYS. AML Stock #002580. 9” x 48” Bridgeport Vertical Milling Machine, Model Series I, S/N 226819 . Table Size 9” x 48” Travels Long 30” Cross 12” Quill 5” Knee 16” Spindle Speeds 60-4200 RPM. 2 HP, 220 Volt, 3 Phase. Taper R-8

Milling Machine, Bridgeport, 2 HP, J Head Variable

Bridgeport Variable Speed Milling Machine 9×42″ Table, Newall X & Y Axis Digital Readout, Servo X axis power feed, R-8 Spindle, 5″ Quill Travel, 2HP 3 Phase 230/460, Serial # 265074 (1994)

Milling Machine, Bridgeport, 1-1/2 HP, J Head

Bridgeport 1-1/2 HP Variable Speed Milling Machine, 9″ x 36″ Table, R-8 Spindle, 3 Phase 230/460 Volts, Serial #107193(1967)

Bridgeport 9 x 48" 3 HP 230v Variable Speed Pulley

Bridgeport 9 x 49" 2 HP Variable Speed Pulley Control 3 Phase Knee Milling Machine 36" Long Travel, 12" Cross Travel, 16" Knee Travel, 60 to 4200 Rpm, Variable Speed $20,814.17 Add to Cart

Milling Variable Speed

A Guide to Renovating the Bridgeport 2J Variable Speed Milling Machine" our 152 page soft cover shop manual, is fully illustrated with over 400 B&W photographs and diagrams, plus step-by-step instructions for disassembling, cleaning, reassembling and adjusting all of the critical components of the variable speed 2J head milling machine.

SERIES I MILLING MACHINES Fab Central

2017-4-21 VARIABLE SPEED DIAL Variable Speed Dial “B”, Figure 2.3, visibly indicates, in windows, the speed range that the machine is operating in, 60 to 500 low range, 500 to 4200 high range. 2-2 M-450 Figure 2.2 High-Low Range Switch A TP5286 Figure 2.3 Variable Speed Dial TP5287 B

Bridgeport Milling Machine Manual The Curious Forge

2018-7-12 These are intended for informational purposes only and not responsible for any injury or damage to the machine Removal of motor on a variable speed head Turn the spindle on and crank the RPM's down to the lowest RPM Shut off the spindle disconnect the power to the machine Remove the drum switch from the left side of the machine

AC Variable Speed Drive H&W Machine Repair &

AC Variable Speed Drive. Retro-fit package for Bridgeport type milling machines. Technological break-through to enhance your existing milling machine. Fully enclosed, solid state heads-up controls with finger tip speed control! -Eliminate- Variable drive discs and their annoying maintenance problems forever.

Bridgeport 2J (Variable Speed) Head Rebuild

The normal rebuild for a Variable Speed is $1,900 $2,300 (this is dependent on the extent of the damage). The rebuild should take two to three days to complete once on the bench. There is usually a 1-3 week lead time from the head arriving to it going up on the bench. Please give us a call at 1-800-285-5271 with any questions you might have. 1.

Milling Machine, Bridgeport, 2 HP, J Head Variable

Bridgeport Variable Speed Milling Machine 9×42″ Table, Newall X & Y Axis Digital Readout, Servo X axis power feed, R-8 Spindle, 5″ Quill Travel, 2HP 3 Phase 230/460, Serial # 265074 (1994)

BRIDGEPORT 1 1/2 HP VARIABLE SPEED VERTICAL

BRIDGEPORT 1 1/2 HP VARIABLE SPEED VERTICAL MILLING MACHINE WITH BRIDGEPORT SWIVEL VISE AND ASSORTED COLLETS CHROME WAYS, 9" x 42" TABLE. AML Stock #002572. 9” x 42” Bridgeport Vertical Milling Machine, Model 2J, S/N 156719. Table Size 9” x 42” Travels Long 26” Cross 12” Quill 5” Knee 16” Spindle Speeds 60-4200 RPM HP 1.5 220

Milling Machine, Bridgeport, 1-1/2 HP, J Head

Bridgeport 1-1/2 HP Variable Speed Milling Machine, 9" x 36" Table, R-8 Spindle, 3 Phase 230/460 Volts, Serial #107193(1967)

Bridgeport Series II 11" x 58" Variable Speed Vertical

Bridgeport Series II 11" x 58" Variable Speed Vertical Milling Machine quantity. Add to cart. Request Formal Quote. Fill out the form below to receive a quote on this machine. Once the form is filled out, you will be able to see all pricing throughout our website. The Bridgeport Series II Milling Machine

Bridgeport Series 1 9" x 42" Variable Speed Milling

Bridgeport Series 1 9″ x 42″ Variable Speed Milling Machine w/ DRO, Powerfeed, Kurt Vise. (Infinitely Variable): 60 4200 RPM Motor HP: 2 Electrical: 230/460V(Wired 460)/3PH. Equipped With: 2-Axis Digital Readout, Servo Type 140 Power Feed, 6″ Kurt Vise, One Shot Lube. Additional Info: The Milling Machine is in fully functional

0342-470 Bridgeport Model BR2J, Variable Speed

Bridgeport Series 1 Ram Type Vertical Turret Milling Machine, Model BR2J. GUDEL ELECTRONIC ENGRAVING, DUPLICATING, COPY, MEDALLIONS MILLING SYSTEM W/ PRECISE SPINDLE New 1993. Neutec Vacuum Induction Casting Machine Model J15 1 of 2

power drawbar bridgeport milling machine variable

Nice Bridgeport variable spindle speed 2 HP vertical milling machine with a newall C80 2 axis DRO. Table size is 9" x 42" has a x-axis power feed unit and a Kurt power drawbar. This is for local pickup only I will not arrange for shipping but I can load it for you onto a trailer when you come to pick it up.

Bridgeport 9 x 49" Variable Speed Pulley Control 3

The Bridgeport 9 x 49" Variable Speed Pulley Control 3 Phase Knee Milling Machine 36" Long Travel, 12" Cross Travel, 16" Knee Travel, Variable Speed can be found within the Knee Milling Machines category. As part of MSC Industrial Supply's Machinery offering,

Bridgeport Milling Machine Manual The Curious Forge

2018-7-12 These are intended for informational purposes only and not responsible for any injury or damage to the machine Removal of motor on a variable speed head Turn the spindle on and crank the RPM's down to the lowest RPM Shut off the spindle disconnect the power to the machine Remove the drum switch from the left side of the machine

Bridgeport 2J (Variable Speed) Head Rebuild

The normal rebuild for a Variable Speed is $1,900 $2,300 (this is dependent on the extent of the damage). The rebuild should take two to three days to complete once on the bench. There is usually a 1-3 week lead time from the head arriving to it going up on the bench. Please give us a call at 1-800-285-5271 with any questions you might have. 1.

<< Previous:Cyclone Separator For Gold Concentrate Beneficiation
>> Next:Ball Mills Theory